The official 2010 model kit is now here.

This Kit is an updated kit boosting the following changes from the previous version

● GP780 Gyro ( new 3D gyro )
● 450M Motor
● 14T Pinon
● A new style Canopy

GP780:
●Brand new intelligent control logic providing dynamic gain adjustment by detecting current flying conditions, allowing for consistent pirouetting rates during chaos or other demanding 3D maneuvers.
●Utilizes feed forward control logic to boost rudder starting speed, and increase response sensitivity.
●Utilizes Silicon Micro Machines (SMM) sensor with excellent stability to dramatically reduce in-flight tail drifts.
●Utilizes AHTCS (Active Helicopter Tail Control System) to compensate any drift caused by wind direction and force, as well as unintended yaw induced by helicopter itself during flight maneuvers.
●Tailor made specifically for use with high speed digital rudder servos. This gyro festures high sensitivity and minimal reaction time, fully utilizing the potential of modern high speed digital rudder servos.
●Suitable for all sizes of helicopters, from micro indoor to large 90 size glow helicopters.
●Metallic dampening plate built into bottom gyro casing, dramatically increasing anti-vibration and anti-interference abilities.
●Features 1520μs pulse wide and 760μs narrow pulse wide frame rate.
●Digital/Analog servo switchable.
●Reverse switch.
●Rudder servo travel limit adjustment (ATV).
●Mode switch for large/mini helicopter.
●Delay adjustment.
●Gyro locking mode and gain can be adjusted remotely from the transmitter.

Radio transmitter and electronic equipment required for assembly:
1.Transmitter(6-channel or more,helicopter system)
2.Receiver(6-channel or more)
3.Pitch gaugeX1
4.11.1V 3S Li-Po 2000~2200mAh batteryX1

High precision main rotor assembly	High precision bearing mixing arms		Single piece battery mount with integrated canopy mount designed to bring CG closer to disk plane
Single piece integrated design of anti-rotation guide and gyro mount	High precision main drive gear with dual cooling fan design patent		Highly rigid frame with single piece carbon side and bottom plates/1.2mm
Newly designed high resolution swashplate/Single piece integrated design of main bearing block and servo mount	Metal designed tail drive gear assembly		Highly efficient shaft driven tail design
Centripetal forces balance tail rotor holder	Straight-up in-frame rudder servo mount for improved geometry		Metal stabilizer belt
Single piece integrated landing gear	New version of the Fiberglass painted canopy		325 Carbon blades
450M extended high torque brushless motor)	DS410M Digital metal gear servo		RCE-BL35X 35A Brushless ESC
DS520 Digital gear servo and GP780 head lock gyro

This is the TREX 450 PRO Super Combo kit from Align. The 450 PRO is a completely new T-Rex 450 design by Jason Krause.

Building upon the extremely successful line of it's T-Rex 450 predecessors this new design incorporates the latest in technology to further improve it's great handling and flight characteristics. Single plate Carbon Fiber side frames not only create a stronger frame but also minimize the total parts count.

The improved servo and linkage layouts provide more accurate control to the swashplate and the completely new head design. The larger and more powerful tail uses counter weighted blade grips to achieve better response and holding power and at a reduced tail RPM which results in more reliability and less maintenance. And to top it all off a restyled canopy makes it a stand out from all the others! 

Features:

Newly designed head block with high rigidity and stability.

Single piece integrated design of main bearing block and servo mount.

Single piece integrated design of anti-rotation guide and gyro mount.

Single piece integrated landing gear.

Highly stable flybar control system.

High precision bearing mixing arms.

Newly designed high resolution swashplate.

Single piece battery mount with integrated canopy mount designed to bring CG closer to disk plane.

Highly rigid frame with single piece carbon side and bottom plates.

Highly efficient shaft driven tail design.

Weighted tail rotor blade grips to repel centripetal forces.

Straight-up in-frame rudder servo mount for improved geometry.

Newly designed aerodynamic canopy.

Newly designed high torque motor.

Newly designed high strength main blade grips.

Specifications:

Length: 635mm

Height: 230mm

Main Rotor: 710mm

Tail Rotor: 158mm

Motor Gear: 14T

Main Gear: 150T

Autorotation Tail Drive Gear: 106T

Tail Drive Gear: 25T

Drive Gear Ratio: 1:11.5:4.24

Weight (without power system): 450g

Weight (including power system): 780g

Brushless Motor: 450M Brushless motor(3500KV)

ESC: RCE-BL35X (35A)

Package Includes:

Align T-Rex 450 Pro Super Kit (unassembled)

Black CF Main Frame

325mm Carbon Fiber Rotor Blades 

450M Brushless motor(3500KV)

RCE-BL35X (35A) Brushless Motor ESC

3 - DS410M Metal Gear Servos

1 - GP780 Head Lock Gyro

1 - DS520 Digital Servo

English Manual